Skip to content
Header Dynamic Mixer LVB-Series

ENTEC® Dynamic mixer LVB-Series

Image is not available

Aerospace technology +
Fluid dynamics +
Entec engineering =
Revolutionary results!

Aerospace technology +
Fluid dynamics +
Entec engineering =
Revolutionary results!

Aerospace technology +
Fluid dynamics +
Entec engineering =
Revolutionary results!

Header Dynamic Mixer LVB-Series
Shadow

ENTEC® dynamic mixer LVB-Series

Both the innovative mixing body and the drive shaft are made entirely of stainless steel (absolutely no osmosis is possible). Partly due to the choice of materials and modifications to the design bases, the mixer has evolved into (as good as) indestructible! Now recognized in various industries such as: (waste)water treatment plants (WWTP), (petro)chemical-, cosmetic-, concrete-, paint- and paper industries.

Specifications
Mixer (with aeration module options)
Stainless Steel-mixer and driveshaft
Anti clogging technology
Situation-specific calculated gearbox with maximum service factor
Power range 0,55 kW – 22 kW
Mixing body Ø 1500 – 2300 mm
Advantages
Efficient nitrogen and phosphate reduction through homogenisation
Minimum surface turbulence
Minimum energy input
Maximum return
Minimum short-circuit currents
Highest return/mixing output with the ENTEC® dynamic / hyperboloid mixer

A flow is generated in the basin which runs parallel to the mixing body surface, due to our unique design of the mixing body (patent pending). The transport ribs, integrated on the mixing body, provide a flow of the medium in a radial direction and thus mix the entire content of the basin. A turbulent flow from the mixer to the basin wall runs across the bottom of the basin, which favors the swirling of sludge particles.

Lowest energy consumption with the ENTEC® dynamic / hyperboloid mixer

The mixing output is generated by a relatively small electromotor, specially calculated, tailored and selected for your basin and fluid. Our R&D department developed special calculation software for our mixing technology. With this software we will always deliver the highest output – lowest energy consumption ratio, adjusted to your specific situation. 

Low maintenance

The lifespan compared with underwater mixers is considerably larger due to the drive being dry lined up on a bridge construction. This allows easy access for maintenance on deck when needed. But in reality, this will only be a refreshment of oil in a few years. Our mixing body and driveshaft are made of stainless steel, provided with a special coating.

Therefore almost unbreakable and free of osmosis formation. This makes our solution unique and really sustainable compared with conventional (old) mixers, which are mostly made of some type of plastic. All this limit your maintenance and repair efforts to such a low level that we have classified it as “no maintenance”.

Versatile in application​

Our range of sizes in combination with our calculation software and technical knowhow, allow us to keep tanks of 100 litres to basins of 1,500 m3 in suspension per mixing body. The mixer is simple, robust, corrosion-resistant, low-maintenance and therefore applicable everywhere. 

Aerating options

Optional to our mixing solution is the addition of an aerating module, mostly used in the process of (SBR) wastewater treatment. Air or gas is introduced under the dynamic / hyperboloid mixing body via a separate connection. When the mixing body rotates, the air is intensively mixed with the medium and divided into very fine bubbles. The main flow transports these fine bubbles radially towards the outside and distributes them throughout the whole tank.

Turnkey solution

We go the extra mile and do not stop at just delivering high-end materials. You can always expect the best guidance, advice and complete solution that fits your situation. Your problem, our solution!

Area of operations

We provide solutions to customers worldwide, and therefore do not hesitate to contact us wherever you are located. All of our operations are coordinated from our headquarters based nearby Rotterdam, The Netherlands, Europe.

We go the extra mile and do not stop at just delivering high-end materials. You can always expect the best guidance, advice and complete solution that fits your situation. Your problem, our solution!

For all national enquiries we would like to refer you to our Dutch websites:​
www.entec-holland.nl and/or www.entec-wtb-engineering.nl

In addition to the LVB Series, Entec International also has other different types of dynamic mixers in the range, so that we can always meet your demand.
Click here for an overview of the dynamic mixers.